Alarm Lock ETPLN Guia do Utilizador descarregar pdf (Página 19)

DL-WINDOWS™ for Trilogy Networx™ V4.0 USER'S GUIDE 19

to warn of the possible malfunction. Green colored fields

indicate the attributes are within acceptable limits as set

by DL-Windows. To exit this screen, click Close. Note:

For new installations, some data may not yet exist, and

therefore several fields may be empty.

5. Discover physical locks on the Gateway

Each Networx

™

lock is identified by a unique serial num-

ber assigned and programmed into the lock firmware at

the factory. To find installed locks, click the GW Confg

button to open the Gateway Configuration screen.

As shown in the "SELECTING A GATEWAY" image,

click to highlight and select the Gateway to which you

want to assign ("add") the installed locks. The Gateway

selected will transmit the discovery request radio signal

to the locks in the vicinity. Only those locks within range

that have not already been configured will respond.

The maximum search time allowed for each discovery

request is 1 minute. To minimize the search time, this

screen allows you to limit the search to a certain quantity

of installed locks. In addition, you can manually stop the

discovery process at any time by pressing the Esc key

on the keyboard. If you know the number of installed

locks to be discovered, select that number and the dis-

covery process will stop the moment that number of

locks are found. If the number of locks selected exceeds

the actual number physically installed, the discovery

process will continue for either a maximum of 1 minute or

until the Esc key is pressed.

Example: If the number selected is 10, but in fact only 8

locks exist, the system may find all 8 locks, but will keep

searching for 10 until the one minute timeout duration

expires--or until the Esc key is pressed.

Click the Number of Locks to Discover pull-down list

and select a number of locks that you want to detect.

Click the Discover Locks On Selected Gateway button

to initiate the search.

The "DISCOVERED LOCK" image displays the results

when one lock was requested to be discovered and one

lock was found:

6. Assign (add) discovered locks to the Gateway

In "DISCOVERED LOCK" example image, a popup

screen entitled "Discovered 1 Locks" appears, indicat-

ing the serial number of the lock, the signal strength and

the lock model.

To assign ("add") the discovered lock serial number(s) to

the selected Gateway, click the check box next to each

lock. To assign, click Use Selected Locks; to exit with-

out assigning ("adding") any locks, click Cancel.

Note: When the Use Selected Locks button is clicked

(in the "Discovered Locks" popup), the Gateway sends

"configuration data" to the selected locks. This

"configuration data" contains items (such as an internal

lock designation, a specific radio channel and security

data) that are all embedded in what is called a "Lock Con-

fig Table". This "configuration data" instructs the physical

lock(s) to communicate ONLY with that Gateway and pre-

vents other Gateways from communicating with the

physical lock(s).

7. Link lock to a Profile.

In DL-Windows, the word "Link" is used to describe the

specific action of associating a "virtual lock" Profile to the

serial number of the physical lock installed on the door.

After clicking Use Selected Locks, a Link Locks popup

appears, asking if you want to link your new locks now

(see LINK LOCKS POPUP). Click Yes to open the

Link/Unlink Lock Profiles screen or click No to cancel.

(see LINK / UNLINK PROFILES image).

LINK LOCKS POPUP

Configuring DL-Windows for Wireless Lock Use (cont'd)

Click a row to highlight

and select a Gateway.

SELECTING A GATEWAY

DISCOVERED LOCK

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 67 68

Comentários a estes Manuais

Sem comentários

Alarm Lock ETPLN Guia do Utilizador Página 19

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Alarm Lock ETPLN