Alarm Lock Trilogy DL3500 Manual de Instruções descarregar pdf (Página 24)

; 6 7 ; [ _ _ ] :

(Event Number)

67. Add System Features

SYSTEM FEATURES

68. Delete All Relay Features added by Function 67.

; 6 8 ; 0 0 0 :

• Relay Features (12-24. Reserved)

1. Remote Input switch closed and Function 65 Remote Input

enabled. Because the Remote Input is enabled by factory default,

the Relay will energize when the Remote Input switch is closed.

7. Scheduled Lock Event. Relay energizes for 2 seconds when lock

is locked by a Schedule.

2. Remote Input switch closed and Function 64 Remote Input

disabled. If the Remote Input is disabled with Function 64, the Re-

lay will NOT energize when the Remote Input Switch is closed.

8. Scheduled Unlock Event. Relay energizes for 2 seconds when

lock is unlocked by a schedule

3. Failed attempted entry. Relay energizes for 2 seconds when an

attempted User Code entry via the keypad fails.

9. Lock Out. Relay energizes for 2 seconds when a Lock Out occurs

(i.e. number of attempts is exceeded, see Function 60).

4. Disabled User or Group. Relay energizes for 2 seconds when a

disabled User or disabled Group member enters a User Code.

10. Ambush. Relay energizes for 2 seconds when Ambush is tripped.

See Function 66, page 25.

5. Follow Access Granted. When a valid User Code is entered into

the keypad and the lock unlocks, the Relay energizes for 2 seconds.

Compare with Event 31.

11. First Key Press. Relay energizes for 2 seconds at the first key

press of any sequence.

6. Group 1 User Code. Relay energizes for 2 seconds when a sched-

uled Group 1 User Code is entered. See Function 90, page 29.

31. Follow Access Granted--No Time Limit.** When a valid User

Code is entered into the keypad and the lock unlocks, the Relay

energizes for the same amount of time as the programmed Pass

Time. (The Pass Time is the length of time the lock stays

unlocked after a valid User Code is entered. See functions

52-54). Use this feature for remote monitoring or other activation.

Use Function 67 to program one or more lock events and the Relay will energize when the programmed event(s) listed below oc-

curs. For example, program ; 6 7 ; 3 : and when an attempted entry fails (such as a User who enters an

incorrect or un-programmed User Code), the Relay will energize for 2 seconds. Note: For more information about the Remote In-

put, see page 11 (Wiring, Remote Input) and page 25 (Function 65).

• System Options

25. Disable Sounder

26. 5 sec. Delayed Entry *

27. 15 sec. Delayed Entry *

28. 45 sec. Delayed Entry *

• Remote Input Functions

29. Toggle Passage Mode. Remote Input toggles Passage

Mode.

30. Forced Unlock Follows Remote Input.** When Remote

Input activated, the Relay will energize regardless of its cur-

rent state.

32. Remote Input Disables Unit.** Regardless of the current

state, that state will remain unchanged (and keypad will be

disabled) for the duration of Remote Input switch closure.

* Features 26, 27 & 28 will delay User Codes 12 and higher only (except 297, 298 and 299).

** Features 30, 31 & 32 should be used with External DC Power unless feature is used for short a duration and infrequently (sustained

closure of remote input or Relay will drain batteries, and scheduled events will not occur during sustained closure of remote input).

Sustained closure of remote input may affect proper audit trail operation.

NOTE: Enter ; 6 7 ; 0 0 0 : to delete all Relay Features added by Function 67 (identical to Function 68).

• PC Communication Functions

33. Remote Input Puts Unit in PC Communication Mode

Enter ; 6 8 ; 0 0 0 : to delete all Relay Features added by Function 67.

Programming Functions (cont'd)

Ambush Function

1. Connect relay to a device able to properly monitor dry contacts for an Ambush condition.

2. Program the Relay for Ambush Tripped using Program Function 67(10) above.

3. Set the Ambush Code using Program Function 66.

4. When the Ambush Code is entered followed by a valid User Code, the relay will close for 2 seconds.

Notes: The Ambush Code defaults to 99. An error will sound if you try to program a new User Code starting with the Ambush Code.

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 35 36

Comentários a estes Manuais

Sem comentários

Alarm Lock Trilogy DL3500 Manual de Instruções Página 24

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Alarm Lock Trilogy DL3500